PassLeader 100% Pass Ensure Juniper JN0-333 Dumps VCE and Dumps PDF (Question 41 – Question 45)

The newest Juniper JN0-333 dumps are available from PassLeader, you can get both JN0-333 VCE dumps and JN0-333 PDF dumps from PassLeader! PassLeader have added the newest JN0-333 exam questions into its JN0-333 VCE and PDF dumps now, the new JN0-333 braindumps will help you 100% passing the JNCIS-SEC JN0-333 exam. Welcome to download the valid PassLeader JN0-333 dumps VCE and PDF here: https://www.passleader.com/jn0-333.html (105 Q&As Dumps –> 116 Q&As Dumps)

Besides, download that PassLeader JN0-333 braindumps from Google Drive: https://drive.google.com/open?id=0B-ob6L_QjGLpNzNvWWE1ck01MHM (FREE VERSION!!!)

QUESTION 41
What is the function of redundancy group 0 in a chassis cluster?

A.    Redundancy group 0 identifies the node controlling the cluster management interface IP addresses.
B.    The primary node for redundancy group 0 identifies the first member node in a chassis cluster.
C.    The primary node for redundancy group 0 determines the interface naming for all chassis cluster nodes.
D.    The node on which redundancy group 0 is primary determines which Routing Engine is active in the cluster.

Answer: D

QUESTION 42
Clients at a remote office are accessing a website that is against your company Internet policy. You change the action of the security policy that controls HTTP access from permit to deny on the remote office SRX Series device. After committing the policy change, you notice that new users cannot access the website but users that have existing sessions on the device still have access. You want to block all user sessions immediately. Which change would you make on the SRX Series device to accomplish this task?

A.    Add the set security flow tcp-session rst-invalidate-session option to the configuration and commit the change.
B.    Add the set security policies policy-rematch parameter to the configuration and commit the change.
C.    Add the security flow tcp-session strict-syn-check option to the configuration and commit the change.
D.    Issue the commit full command from the top of the configuration hierarchy.

Answer: B

QUESTION 43
You are asked to support source NAT for an application that requires that its original source port not be changed. Which configuration would satisfy the requirement?

A.    Configure a source NAT rule that references an IP address pool with interface proxy ARP enabled.
B.    Configure the egress interface to source NAT fixed-port status.
C.    Configure a source NAT rule that references an IP address pool with the port no-translation parameter enabled.
D.    Configure a source NAT rule that sets the egress interface to the overload status.

Answer: C

QUESTION 44
What are three valid virtual interface types for a vSRX? (Choose three.)

A.    SR-IOV
B.    fxp0
C.    eth0
D.    VMXNET 3
E.    virtio

Answer: ABD

QUESTION 45
Referring to the exhibit, which statement is true?
passleader-JN0-333-dumps-451

A.    TCP packets entering the interface are failing the TCP sequence check.
B.    Packets entering the interface are being dropped due to a stateless filter.
C.    Packets entering the interface are getting dropped because there is no route to the destination.
D.    Packets entering the interface matching an ALG are getting dropped.

Answer: C


Thanks for reading the newest JN0-333 exam dumps! We recommend you to try the PREMIUM PassLeader JN0-333 dumps in VCE and PDF here: https://www.passleader.com/jn0-333.html (105 Q&As Dumps –> 116 Q&As Dumps)

Also, you can download that PassLeader JN0-333 braindumps from Google Drive: https://drive.google.com/open?id=0B-ob6L_QjGLpNzNvWWE1ck01MHM (FREE VERSION!!!)