PassLeader 100% Pass Ensure Juniper JN0-360 Dumps VCE and Dumps PDF (Question 1 – Question 30)

The newest Juniper JN0-360 dumps are available from PassLeader, you can get both JN0-360 VCE dumps and JN0-360 PDF dumps from PassLeader! PassLeader have added the newest JN0-360 exam questions into its JN0-360 VCE and PDF dumps now, the new JN0-360 braindumps will help you 100% passing the JNCIS-SP JN0-360 exam. Welcome to download the valid PassLeader JN0-360 dumps VCE and PDF here: https://www.passleader.com/jn0-360.html (372 Q&As Dumps)

Besides, download that PassLeader JN0-360 braindumps from Google Drive: https://drive.google.com/open?id=0B-ob6L_QjGLpfnN5YmVFZ194RmwtOUJlWkVoSmV3RzNUcUhpYjlmU1U3NEVyYUxHQWdjMms (FREE VERSION!!!)

QUESTION 1
What are two valid actions that can be applied to a frame by a Layer 2 firewall filter? (Choose two.)

A.    Log
B.    loss-priority
C.    sample
D.    count

Answer: BD

QUESTION 2
Which two statements describe differences between IPv4 and IPv6? (Choose two.)

A.    IPsec is built into IPv6
B.    IPv6 uses a 32-bit (4-byte) address and can support up to 4,294,967,296 addresses
C.    IPv4 supports extension headers whereas IPv6 options are integrated into the base
D.    IPv6 eliminates the need for NAT

Answer: AD

QUESTION 3
You must configure an OSPF area that does not accept type 3 link-state advertisements (LSAs) from area 0 (other than the default route) You have configured your area to be stub, but you still see type 3 LSAs. What will account for this behavior?

A.    You should have configured your area as totally stubby
B.    You should have used a not-so-stubby-area
C.    You are experiencing a routing loop
D.    You have exported routes into OSPF

Answer: A

QUESTION 4
You have configured an IP-IP tunnel between Router A and Router B. Which Junos operational mode command is used to verify that the tunnel interface is up and operational?

A.    show chassis tunnel status
B.    show tunnel interface
C.    show interfaces terse
D.    show interfaces tunnel

Answer: C

QUESTION 5
Which IS-IS packet is used to determine the level of an IS-IS neighbor?

A.    IIH
B.    LSP
C.    PSNP
D.    CSNP

Answer: A

QUESTION 6
Router A is an OSPF router connected to both Area 0 and Area 1 Area 1 has been configured as a stub area Which two LSA types does Router A suppress from Area 1?

A.    Router LSA
B.    External LSA
C.    Summary LSA
D.    ASBR Summary LSA

Answer: BD

QUESTION 7
Based on the illustration of the VPLS topology shown in the exhibit, which statement is true?
passleader-jn0-360-dumps-71

A.    PE-C must have a spanning-tree protocol enabled
B.    CE-C must have BGP enabled
C.    Traffic forwarded from PE-C to PE-A is forwarded on to PE-B
D.    Traffic forwarded from PE-C to PE-A is not forwarded on to PE-B

Answer: D

QUESTION 8
You are logged into a router and have navigated to the (edit routing-options] level of the hierarchy. You have been asked to create a static route that will use 10.10.10.1 as its primary next-hop and 10.10.10.5 as its secondary next-hop. Which command correctly configures this scenario?

A.    set static route 8/8 10.10.10.1 qualified-next-hop 10.10.10.5 pref 10
B.    set static route 8/8 next-hop 10.10.10.1 secondary-next-hop 10.10.10.5 preference 10
C.    set static route 8/8 next-hop 10.10.10.1 qualified-next-hop 10.10.10.5 preference 10
D.    set static route 8/8 next-hop [10.10.10.1 10.10.10.5] pref 10

Answer: C

QUESTION 9
Which Junos operational mode command is used to verify that load balancing is working as expected?

A.    show route all
B.    show route extensive
C.    show route balancing
D.    show route forwarding-table

Answer: D

QUESTION 10
Which two values displayed in the output from the show spanning-tree MSTP configuration command must match on all switches participating in the same MSTP region? (Choose two.)

A.    root bridge identifier
B.    authentication checksum
C.    context identifier
D.    configuration digest

Answer: CD

QUESTION 11
Which role does the router ID (RID) have in the BGP route selection process?

A.    The router ID is evaluated immediately after MED to determine route preference
B.    The router ID is evaluated last in the route selection process
C.    The router ID is evaluated after the cluster length and a lower router ID is chosen
D.    The router ID is evaluated after analyzing the IGP metric cost

Answer: B

QUESTION 12
You are logged into a router and have navigated to the [edit routing-options] level of the hierarchy. You have been asked to create a static route that will use 43 18 7 1 as its primary next-hop and 76 1310 2 as its secondary next-hop. Which command correctly configures this setup?

A.    set static route 0/0 76.13.10.2 qualified-next-hop 43.18.7.1 pref 10
B.    set static route 0/0 next-hop 43.18.7.1 secondary-next-hop 76.13.10.2 preference 10
C.    set static route 0/0 next-hop [76.13.10.2 10.10.10.5] pref 10
D.    set static route 0/0 next-hop 43.18.7.1 qualified-next-hop 76.13.10.2 preference 10

Answer: D

QUESTION 13
Referring to the network illustrated in the exhibit, how does router A reach destinations in area 49.2222?
passleader-jn0-360-dumps-131

A.    Router A will use the routes from area 49.2222; it learns from router B
B.    Router A will see the attached bit from router B and create a default route
C.    Router A must have a default route manually configured
D.    Router A will receive a default route in the IS-IS update from router B

Answer: B

QUESTION 14
You have recently implemented a graceful Routing-Engine switchover (GRES) and want to further reduce down time if a Routing Engine (RE) failure occurs. Which two features can be configured on this device to reduce its downtime in this situation? (Choose two.)

A.    VRRP
B.    GR
C.    BFD
D.    NSR

Answer: BD

QUESTION 15
Which BGP state denotes a fully operational session?

A.    Established
B.    Active
C.    Operational
D.    Connect

Answer: A

QUESTION 16
You work for the regional Internet service provider shown in the exhibit You have a partial BGP table and are receiving a 10 100/16 route from your upstream ISP You have been asked to configure a default route that can be sent to your downstream customer This route should forward customer traffic toward your upstream Tier 11SP as long as the 10.100/16 route is present. What would accomplish this goal?
passleader-jn0-360-dumps-161

A.    Create and announce an aggregate default route
B.    Create and announce a static default route with a next-hop of discard
C.    Create and announce a static default route with a next-hop of reject
D.    Create and announce a generated default route
E.    Create an advertise-map with exist-map

Answer: D

QUESTION 17
You have been asked to configure an IPv6 address for a group of interfaces that could belong on different routers. If a packet is sent to that address, it should be received by all routers in the group. Which address type would be suited for these requirements?

A.    Unicast
B.    Multicast
C.    Anycast
D.    Broadcast

Answer: B

QUESTION 18
In the exhibit, OSPF routers R1, R2, R3, and R4 come up, in order, at 1-minute intervals. Which router will be the designated router?
passleader-JN0-360-dumps-181

A.    R1
B.    R2
C.    R3
D.    R4

Answer: A

QUESTION 19
What is the function of the hop limit field in the IPv6 header?

A.    It limits the diameter of the network to 20 hops
B.    It sets the number of hops in the network to be equal to the MPLS header time-to-live (TTL)
C.    It replaces the time-to-live (TTL) field in IPv4
D.    It represents future extensibility to the protocol

Answer: C

QUESTION 20
You have been asked to define a default gateway for traffic leaving a router. This route should use interface so-0/0/0 as its next-hop.Which type of route would be suited for this scenario?

A.    a static route
B.    a generated route
C.    a martian route
D.    an aggregate route

Answer: A

QUESTION 21
In the exhibit, how many full OSPF adjacencies will R3 have?
passleader-JN0-360-dumps-211

A.    0
B.    1
C.    2
D.    3

Answer: C

QUESTION 22
You are asked to design a Layer 2 switched topology that can automatically recover from link failures. Which type of protocol would you consider in your design?

A.    GSTP
B.    LLDP
C.    LFM
D.    MSTP

Answer: D

QUESTION 23
When the Junos configuration shown in the exhibit is applied to the router, which routes in the forwarding table will begin load-balancing packet flows?
passleader-JN0-360-dumps-231

A.    all routes in the forwarding table
B.    all OSPF routes in the forwarding table
C.    all BGP routes in the forwarding table
D.    all RFC1918 routes in the forwarding table

Answer: D

QUESTION 24
You have configured MPLS and RSVP in your network using all of the Junos defaults. You established an LSP in your network which is reporting an up status but no traffic is using it. Which two statements reflect potential causes for this issue? (Choose two.)

A.    The LSP egress address is a physical interface address
B.    family MPLS was omitted from the router configurations
C.    No BGP routes are being advertised from the remote neighbor
D.    The LSP egress address does not match the BGP next-hop address

Answer: CD

QUESTION 25
Using industry best practices, what is true regarding an external BGP session?

A.    BGP neighbors belong to the same AS
B.    BGP neighbors belong to a different AS
C.    BGP sessions rely on a static route for reach ability
D.    BGP sessions will be established between loopback interface addresses

Answer: B

QUESTION 26
You own a home network connecting through an always-on connection and need to assign IPv6 addresses to your routers because you want to follow the guidelines spelled out in RFC 3177. you want to design your network with the correct prefixes. Which prefix would your ISP likely allocate to your network?

A.    47-bit prefix
B.    48-bit prefix
C.    64-bit prefix
D.    128-bit prefix

Answer: B

QUESTION 27
Which two BGP attributes are modified by default when they are passed between external BGP peers? (Choose two.)

A.    MED
B.    AS-Path
C.    Communities
D.    Next Hop

Answer: BD

QUESTION 28
In an RSTP network, the root and designated ports have been elected as shown in the exhibit. What will be the port type of port 1?
passleader-JN0-360-dumps-281

A.    backup port
B.    discarding port
C.    alternate port
D.    listening port

Answer: C

QUESTION 29
Which two statements about BGP are accurate? (Choose two.)

A.    BGP uses UDP port 500 for connectivity.
B.    BGP uses TCP port 179 for connectivity.
C.    External peering sessions require an underlying IGP.
D.    Internal peering sessions require an underlying IGP.

Answer: BD

QUESTION 30
Which two elements contribute to the bridge ID when configuring RSTP? (Choose two.)

A.    designated MAC address
B.    bridge priority
C.    extended system ID
D.    root ID
E.    bridge address

Answer: BE


Thanks for reading the newest JN0-360 exam dumps! We recommend you to try the PREMIUM PassLeader JN0-360 dumps in VCE and PDF here: https://www.passleader.com/jn0-360.html (372 Q&As Dumps)

Also, you can download that PassLeader JN0-360 braindumps from Google Drive: https://drive.google.com/open?id=0B-ob6L_QjGLpfnN5YmVFZ194RmwtOUJlWkVoSmV3RzNUcUhpYjlmU1U3NEVyYUxHQWdjMms (FREE VERSION!!!)