PassLeader Free Juniper JN0-360 Dumps with VCE and PDF (Question 211 – Question 240)

The newest Juniper JN0-360 dumps are available from PassLeader, you can get both JN0-360 VCE dumps and JN0-360 PDF dumps from PassLeader! PassLeader have added the newest JN0-360 exam questions into its JN0-360 VCE and PDF dumps now, the new JN0-360 braindumps will help you 100% passing the JNCIS-SP JN0-360 exam. Welcome to download the valid PassLeader JN0-360 dumps VCE and PDF here: https://www.passleader.com/jn0-360.html (372 Q&As Dumps)

Besides, download that PassLeader JN0-360 braindumps from Google Drive: https://drive.google.com/open?id=0B-ob6L_QjGLpfnN5YmVFZ194RmwtOUJlWkVoSmV3RzNUcUhpYjlmU1U3NEVyYUxHQWdjMms (FREE VERSION!!!)

QUESTION 211
Which two statements are true about virtual switches? (Choose two.)

A.    Multiple virtual switches share a single MAC table.
B.    Virtual switches contain separate MAC tables.
C.    By default, the direct route associated with a virtual switch’s IRB interface is placed in inet.0.
D.    By default, the direct route associated with a virtual switch’s IRB interface is placed in the associated virtual switch’s routing table.

Answer: BC

QUESTION 212
In Q-in-Q tunneling, what is the purpose of the pop-swap operation?

A.    pop the outer tag and swap the inner tag
B.    pop and swap the inner tag
C.    pop and swap both outer and inner tags
D.    pop the inner tag and swap the outer tag

Answer: A

QUESTION 213
What are three components of the tag portion of an 802.1Q-tagged Ethernet frame? (Choose three.)

A.    Tag Protocol Identifier
B.    maximum transmission unit
C.    canonical format indicator
D.    unique VLAN identifier
E.    frame check sequence

Answer: ACD

QUESTION 214
Which three mechanisms are used by switches to build and maintain bridge tables? (Choose three.)

A.    learning
B.    rewriting
C.    flooding
D.    aging
E.    blocking

Answer: ACD

QUESTION 215
What is the purpose of a trunk link?

A.    to carry traffic for multiple VLANs between multiple switches
B.    to interconnect multiple bridging domains on the same switch
C.    to aggregate multiple native VLANs into a single bridging domain
D.    to allow Layer 3 functionality for multiple VLANs

Answer: A

QUESTION 216
What are two differences between RSTP and VSTP? (Choose two.)

A.    Using VSTP, the BPDU destination address is always 01:00:0C:CC:CC:CD.
B.    Using VSTP, the BPDU frame carries an 802.1Q tag.
C.    Using RSTP, the BPDU destination address is always 01:00:0C:CC:CC:CD.
D.    Using RSTP, the BPDU frame carries an 802.1Q tag.

Answer: AB

QUESTION 217
A rogue switch has been added to your network, exchanged BPDUs, and is now part of the spanning tree topology. Which feature would help prevent this from happening in the future?

A.    storm control
B.    BPDU control
C.    root protection
D.    loop protection

Answer: B

QUESTION 218
What is the maximum number of MSTIs supported in an MST region?

A.    32
B.    64
C.    128
D.    256

Answer: B

QUESTION 219
Which two statements are true about STP and RSTP? (Choose two.)

A.    STP uses a proposal-and-agreement handshake on point-to-point links instead of timers.
B.    In RSTP, root ports and edge ports transition to the forwarding state immediately, without exchanging messages with other switches.
C.    In RSTP, a TCN is generated when a port transitions to the discarding state.
D.    In STP, the forwarding delay timer and maximum age timer define the convergence delay.

Answer: BD

QUESTION 220
What are two types of BPDUs in the Spanning Tree Protocol? (Choose two.)

A.    configuration
B.    hello
C.    topology change notification
D.    link state

Answer: AC

QUESTION 221
You are asked to establish an MPLS LSP between two sites. You are required to ensure the LSP traverses specific routers within your network. Which solution is correct?

A.    Enable traffic engineering within LDP and define the explicit route the LSP must follow.
B.    Implement RSVP and define the explicit route the LSP must follow.
C.    Enable traffic engineering within RSVP and define the explicit route the LSP must follow.
D.    Implement LDP and define the explicit route the LSP must follow.

Answer: B

QUESTION 222
Which statement is correct about the inet.3 routing table?

A.    MPLS creates a copy of the mpls.0 table and stores it in the inet.3 routing table.
B.    The inet.3 routing table is used by transit routers to identify label values.
C.    BGP can use the inet.3 routing table to resolve next hops.
D.    MPLS uses the inet.3 routing table to assign labels.

Answer: C

QUESTION 223
Which two statements are correct about default MPLS behavior on Junos devices? (Choose two.)

A.    The MPLS label is popped by the penultimate router.
B.    The MPLS label is popped by the ultimate router.
C.    The MPLS label is pushed by the ingress router.
D.    The MPLS label is swapped by the ingress router.

Answer: AC

QUESTION 224
Which two statements regarding the MPLS label information base are correct? (Choose two.)

A.    The MPLS label information base is stored in the inet.3 table.
B.    The MPLS label information base is stored in the mpls.0 table.
C.    The label information base is used by all LSRs to forward LSP traffic.
D.    The label information base is used by transit LSRs to forward LSP traffic.

Answer: BD

QUESTION 225
Which two statements are correct about RSVP path messages? (Choose two.)

A.    They are sent by the egress router upstream.
B.    They are sent by the ingress router downstream.
C.    They are used to create an LSP.
D.    They are used to reserve resources for an LSP.

Answer: BC

QUESTION 226
Which two statements are correct regarding LDP-signaled VPLS instances? (Choose two.)

A.    You must enable the Layer 2 VPN signaling NLRI.
B.    You must configure the same VPLS identifier on all peers.
C.    You must define a the same site-identifier value on all peers.
D.    You must define all neighbors using their tunnel end-point IP addresses.

Answer: BD

QUESTION 227
Which two statements are correct regarding LDP-signaled Layer 2 circuits? (Choose two.)

A.    You must enable the Layer 2 VPN signaling NLRI.
B.    You must configure the virtual circuit identifier.
C.    You must specify the neighbor using the tunnel end-point IP address.
D.    You must define a unique site-identifier value.

Answer: BC

QUESTION 228
Which two statements are correct regarding BGP-signaled Layer 2 VPNs? (Choose two.)

A.    You must enable the Layer 2 VPN signaling NLRI.
B.    You must configure the virtual circuit identifier.
C.    You must specify the neighbor using the tunnel end-point IP address.
D.    You must define a unique site-identifier value.

Answer: AD

QUESTION 229
Which two statements regarding VRF tables are correct? (Choose two.)

A.    A PE router’s VRF table stores routes received from directly connected CE devices.
B.    A PE router’s VRF table stores routes received from its IGP from remote PE devices.
C.    A PE router’s VRF table stores routes received from MP-BGP from remote PE devices.
D.    A PE router’s VRF table stores routes received from all P and PE devices within the same AS.

Answer: AC

QUESTION 230
You have been asked to implement routing policy on the PE devices in your AS and to ensure the correct customer routes are installed in the appropriate VRF tables. Which component should be used as a match condition within your policy?

A.    BGP communities
B.    VLAN IDs
C.    route distinguisher
D.    circuit IDs

Answer: A

QUESTION 231
What is the purpose of a route target community in a Layer 3 VPN?

A.    The community value is used to identify routes that should be imported by remote PEs.
B.    The community value is used to determine valid remote devices when signaling a Layer 3 VPN.
C.    The community value is used to identify the source of incoming routes.
D.    The community value is used to determine transit devices when signaling a Layer 3 VPN.

Answer: A

QUESTION 232
You have been asked to deploy a Layer 2 VPN for a new customer. What information will be present in the PE’s associated VPN forwarding table? (Choose three.)

A.    the customer site ID
B.    the route distinguisher
C.    the interface encapsulation
D.    the label base
E.    the community name

Answer: ACD

QUESTION 233
You have an established Layer 3 VPN where you are using static routing between your PE and CE devices. You must advertise their directly connected subnet to remote PE devices. Which two methods must you use? (Choose two.)

A.    Use a site identifier.
B.    Use the VRF table label.
C.    Use a VRF export policy.
D.    Use a route distinguisher.

Answer: BC

QUESTION 234
You have been asked to verify the state of an LDP-signaled Layer 2 circuit. Which two commands would you use to verify the state of the connection? (Choose two.)

A.    show mpls lsp
B.    show l2circuit connections
C.    show l2circuit statistics
D.    show ldp database

Answer: BD

QUESTION 235
What are two valid IPv6 addresses? (Choose two.)

A.    2bfc::02 :0:0:fe c:5c
B.    2bfc::2 ::fe c:5c
C.    2bfc:2 :0:0:fe c:5c
D.    2bfc:0:0:2 ::fe c:5c

Answer: AD

QUESTION 236
Which new field is added to the IPv6 header when compared to IPv4?

A.    version
B.    fragment offset
C.    checksum
D.    flow label

Answer: D

QUESTION 237
Which three are valid IPv6 extension headers? (Choose three.)

A.    multicast header
B.    authentication header
C.    autoconfiguration options
D.    fragment
E.    hop-by-hop options

Answer: BDE

QUESTION 238
What are two components of an IPv6 router advertisement message? (Choose two.)

A.    DHCPv6 request
B.    Layer 2 address of advertising router
C.    duplicate address detection notification
D.    link MTU

Answer: BD

QUESTION 239
Which two statements are correct about neighbor discovery in IPv6? (Choose two.)

A.    Neighbor discovery relies on ARP to find neighbors on a local link.
B.    A neighbor is considered reachable when the neighboring device responds to a neighbor solicitation message.
C.    A neighbor is considered reachable when the neighboring device responds to a router solicitation message.
D.    Neighbor discovery does not use ARP to find neighbors on a local link.

Answer: BD

QUESTION 240
You want to configure an interface on your router to use an IPv6 global IP address. Which three methods accomplish this task? (Choose three.)

A.    Use stateless autoconfiguration to assign only the 64 bit interface ID.
B.    Use stateful autoconfiguration to assign only the 64 bit interface ID.
C.    Use stateful autoconfiguration to assign the entire global IPv6 address.
D.    Use a statically assigned global IPv6 address.
E.    Use stateless autoconfiguration to assign the entire global IPv6 address.

Answer: ACD


Thanks for reading the newest JN0-360 exam dumps! We recommend you to try the PREMIUM PassLeader JN0-360 dumps in VCE and PDF here: https://www.passleader.com/jn0-360.html (372 Q&As Dumps)

Also, you can download that PassLeader JN0-360 braindumps from Google Drive: https://drive.google.com/open?id=0B-ob6L_QjGLpfnN5YmVFZ194RmwtOUJlWkVoSmV3RzNUcUhpYjlmU1U3NEVyYUxHQWdjMms (FREE VERSION!!!)