[13-Dec-2021] New PassLeader JN0-648 JNCIP-ENT Dumps with VCE and PDF (New Questions)

The newest Juniper JN0-648 dumps are available from PassLeader, you can get both JN0-648 VCE dumps and JN0-648 PDF dumps from PassLeader! PassLeader have added the newest JN0-648 exam questions into its JN0-648 VCE and PDF dumps now, the new JN0-648 braindumps will help you 100% passing the JNCIP-ENT JN0-648 exam. Welcome to download the valid PassLeader JN0-648 dumps VCE and PDF here: https://www.passleader.com/jn0-648.html (120 Q&As Dumps)

Besides, download that PassLeader JN0-648 braindumps from Google Drive: https://drive.google.com/open?id=1WgttZ1C6y6hC2jklqIw4EWJ7Odb2bKJR (FREE VERSION!!!)

Which BGP message type contains NLRI information?

A.    notification
B.    keepalive
C.    update
D.    open

Answer: C

You are implementing a single spanning tree instance in your network and want to use the protocol that will give you the best convergence time in the event of a physical network failure of the root bridge. Which spanning tree protocol will satisfy this requirement?

A.    RSTP
B.    STP
C.    MSTP
D.    VSTP

Answer: A
STP and RSTP are limited to a single instance on any physical interface. Use the interface (Spanning Tree) statement to configure interfaces to participate in the STP or RSTP instance.

You have configured CoS on a Junos device. A packet is classified as best effort by a behavior aggregate (BA) classifier, and as expedited forwarding by a multifield (MF) classifier. Which statement is true in this scenario?

A.    The packet will be placed in a queue associated with the BA classifier.
B.    The packet will be placed into the queue which is least congested.
C.    The packet will be placed into the queue that has the most bandwidth assigned to it.
D.    The packet will be placed in a queue associated with the MF classifier.

Answer: D
If you configure both a behavior aggregate (BA) classifier and a multifield classifier, BA classification is performed first; then multifield classification is performed. If they conflict, any BA classification result is overridden by the multifield classifier.

You must ensure that all management traffic sourced from your Junos devices is set with a specific DSCP code-point value. Which action will accomplish this task?

A.    Apply the DSCP code-point to the [edit class-of-service host-outbound-traffic] hierarchy.
B.    Apply the DSCP code-point to the [edit class-of-service interface lo0.0] hierarchy.
C.    Apply the DSCP code-point in an egress policer.
D.    Apply the DSCP code-point to a rewrite rule.

Answer: A
To change these default settings, include the forwarding-class class-name statement and the dscp-code-point value statement at the [edit class-of-service host-outbound-traffic] hierarchy level. This feature does not affect transit traffic or incoming traffic.

You notice a mass withdrawal of routes for some of the network hosts. You determine that the link on the ESI interface is down. Which route type is used in this scenario?

A.    Type 2
B.    Type 3
C.    Type 1
D.    Type 5

Answer: C
This is a Type 1 mandatory route, used for fast convergence and for advertising the split horizon label. It is also known as the mass withdraw route.

You have an MX960 configured as a Fusion aggregation device (AD) and two QFX5100 switches as satellite devices (SD). You have configured local-switching for each SD. A packet with an unknown MAC address is received on one of the SD extended ports. Which statement is correct in this scenario?

A.    The packet is dropped and a reject message is sent out to the port where it was received.
B.    The packet is silently discarded and a reject message is sent to the AD.
C.    The packet is flooded out of all the ports on the SD except the one where it was received.
D.    The packet is sent to the AD to be processed and forwarded.

Answer: D

You are using 802.1X in your access network consisting of EX Series switches. You recently had a failure with your RADIUS server which resulted in authenticating client devices being denied access to the network. You want to change this behavior so that authenticating clients are directed to a remediation VLAN. Which RADIUS server failback setting satisfies this requirement?

A.    permit
B.    move
C.    sustain
D.    deny

Answer: B

You have configured class mode power management on an EX4300 to provide PoE power to telephone and security camera equipment. You want to ensure that security camera power takes priority over telephone power. Which two actions would solve this problem? (Choose two.)

A.    Connect the security cameras to the lowest port numbers on the switch.
B.    Set the power priority to high on ports connected to security cameras.
C.    Set the maximum power settings on ports connected to security cameras.
D.    Set the power priority to low on ports connected to security cameras.

Answer: AB
Thus you must set interfaces that connect to critical powered devices, such as security cameras and emergency phones, to high priority. Among PoE interfaces that have the same assigned priority, power priority is determined by the port number, with lower-numbered ports having higher priority.

You have multiple BGP routes to the same prefix with equal local-preference values and AS-path lengths. In this scenario, which route will be preferred in the route selection process?

A.    The route with the least preferred origin value.
B.    The route with the lowest MED value.
C.    The route with the most preferred origin value.
D.    The route with the highest MED value.

Answer: C

You have an IPv4 multicast network configured as PIM-SM. What must be done before replacing your static RP with auto-RP?

A.    Enable sparse-dense mode on each of the routers in the network.
B.    Configure auto-RP domains on each router in the network.
C.    Configure each router in the network as a candidate BSR.
D.    Enable each router in the network to forward multicast packets.

Answer: A
Because PIM dense mode is necessary to enable auto-RP to work, which in turns enables PIM sparse mode to work, you must configure PIM sparse-dense mode in the PIM domains that use auto-RP.

Your company has expanded into office space across the street. The new office space has a single Ethernet connection connected to an unmanaged switch. You must sort traffic based on the IP address into different VLANs once the traffic arrives on your EX Series switches. Which mechanism would you use to accomplish this task?

A.    MVRP
B.    filter-based VLANs
C.    Q-in-Q tunneling
D.    dynamic VLANs

Answer: B

Referring to the exhibit:
How is R5 able to learn the networks that exist within the NSSA?

A.    R5 learns those networks from Type 3 LSAs advertised by R2.
B.    R5 learns those networks from Type 3 LSAs advertised by R3.
C.    R5 does not learn those networks and uses a default route advertised by R3 instead.
D.    R5 does not learn those networks but uses a default route advertised by R2 instead.

Answer: B

Referring to the exhibit:
You must advertise the routes from AS1 to AS2, but R2 is not advertising any BGP routes to R5. Why is this happening in this scenario?

A.    The IBGP routes will not be advertised because you must use a policy to advertise IBGP routes.
B.    The IBGP routes are not active and EBGP will advertise only active routes.
C.    The IBGP routes will not be advertised because the AS path shows as incomplete.
D.    The IBGP routes are not active because the next hop is not reachable.

Answer: B

Referring to the exhibit:
The source is currently sending multicast traffic using group, which is being received by R1. R2 is not receiving PIM register messages. What would be the cause of this problem?

A.    Tunnel services have not been enabled on R1.
B.    All routers have not been configured with the same Auto-RP discovery group.
C.    R5 has not received an IGMP report of
D.    A(*,G) tree has not been built yet.

Answer: A
The multicast traffic being sent by the source must be encapsulated into a PIM register packet. If the tunneling services under the chassis stanza is not configured, a PE (PIM Encapsulation interface) will not be present in the multicast first hop router. Anyway long story short, tunneling services must be turned on or else you will not get PIM register messages sent to the RP.


Thanks for reading the newest JN0-648 exam dumps! We recommend you to try the PREMIUM PassLeader JN0-648 dumps in VCE and PDF here: https://www.passleader.com/jn0-648.html (120 Q&As Dumps)

Also, you can download that PassLeader JN0-648 braindumps from Google Drive: https://drive.google.com/open?id=1WgttZ1C6y6hC2jklqIw4EWJ7Odb2bKJR (FREE VERSION!!!)