Passing Guarantee Juniper JN0-370 Dumps from PassLeader JN0-370 VCE and PDF for Free (Question 161 – Question 180)

The newest Juniper JN0-370 dumps are available from PassLeader, you can get both JN0-370 VCE dumps and JN0-370 PDF dumps from PassLeader! PassLeader have added the newest JN0-370 exam questions into its JN0-370 VCE and PDF dumps now, the new JN0-370 braindumps will help you 100% passing the JNCIS-QF JN0-370 exam. Welcome to download the valid PassLeader JN0-370 dumps VCE and PDF here: (281 Q&As Dumps)

Besides, download that PassLeader JN0-370 braindumps from Google Drive: (FREE VERSION!!!)

In the exhibit, OSPF routers R1, R2, R3, and R4 come up, in order, at 1-minute intervals Which router will be the designated router?

A.    R1
B.    R2
C.    R3
D.    R4

Answer: A

You have been asked to configure an IPv6 address for a group of interfaces that could belong on different routers. If a packet is sent to that address, it should be received by all routers in the group. Which address type would be suited for these requirements?

A.    Unicast
B.    Multicast
C.    Anycast
D.    Broadcast

Answer: B

What is the function of the hop limit field in the IPv6 header?

A.    It limits the diameter of the network to 20 hops
B.    It sets the number of hops in the network to be equal to the MPLS header time-to-live (TTL)
C.    It replaces the time-to-live (TTL) field in IPv4
D.    It represents future extensibility to the protocol

Answer: C

In the exhibit, how many full OSPF adjacencies will R3 have?

A.    0
B.    1
C.    2
D.    3

Answer: C

You have been asked to define a default gateway for traffic leaving a router. This route should use interface so-0/0/0 as its next-hop. Which type of route would be suited for this scenario?

A.    a static route
B.    a generated route
C.    a martian route
D.    an aggregate route

Answer: C

You are asked to design a Layer 2 switched topology that can automatically recover from link failures. Which type of protocol would you consider in your design?

A.    GSTP
B.    LLDP
C.    LFM
D.    MSTP

Answer: D

When the Junos configuration shown in the exhibit is applied to the router, which routes in the forwarding table will begin load-balancing packet flows?

A.    all routes in the forwarding table
B.    all OSPF routes in the forwarding table
C.    all BGP routes in the forwarding table
D.    all RFC1918 routes in the forwarding table

Answer: D

You have configured MPLS and RSVP in your network using all of the Junos defaults. You established an LSP in your network which is reporting an up status but no traffic is using it. Which two statements reflect potential causes for this issue? (Choose two.)

A.    The LSP egress address is a physical interface address
B.    family MPLS was omitted from the router configurations
C.    No BGP routes are being advertised from the remote neighbor
D.    The LSP egress address does not match the BGP next-hop address

Answer: CD

Using industry best practices, what is true regarding an external BGP session?

A.    BGP neighbors belong to the same AS
B.    BGP neighbors belong to a different AS
C.    BGP sessions rely on a static route for reach ability
D.    BGP sessions will be established between loopback interface addresses

Answer: C

You own a home network connecting through an always-on connection and need to assign IPv6 addresses to your routers because you want to follow the guidelines spelled out in RFC 3177. You want to design your network with the correct prefixes. Which prefix would your ISP likely allocate to your network?

A.    47-bit prefix
B.    48-bit prefix
C.    64-bit prefix
D.    128-bit prefix

Answer: B

Which two BGP attributes are modified by default when they are passed between external BGP peers? (Choose two.)

A.    MED
B.    AS-Path
C.    Communities
D.    Next Hop

Answer: BD

Which two statements about BGP are accurate? (Choose two.)

A.    BGP uses UDP port 500 for connectivity.
B.    BGP uses TCP port 179 for connectivity.
C.    External peering sessions require an underlying IGP.
D.    Internal peering sessions require an underlying IGP.

Answer: BD

In an RSTP network, the root and designated ports have been elected as shown in the exhibit. What will be the port type of port 1?

A.    backup port
B.    discarding port
C.    alternate port
D.    listening port

Answer: A

Which three statements are correct about the QFabric system control plane? (Choose three.)

A.    It discovers and manages paths.
B.    It manages FCoE-to-FC conversions.
C.    It manages Layer 2 and Layer 3 load balancing between nodes and interconnects.
D.    It discovers and provisions the system.
E.    It manages routing and switching protocols.

Answer: ADE

The QFabric system data plane performs which three functions? (Choose three.)

A.    It provides connectivity for network devices.
B.    It manages routing and switching protocols.
C.    It interconnects Node devices with the fabric.
D.    It exchanges reachability information.
E.    It forwards traffic through devices of the system.

Answer: ACE

You are determining the DC power requirements for a QFX3000-M QFabric system. Which two devices support DC power? (Choose two.)

A.    a QFX3100 Director device
B.    a QFX3600-I Interconnect device
C.    a QFX3500 Node device
D.    a QFX3800-I Interconnect device

Answer: BC

You configured a BGP peering session between your QFabric system and an attached device, but the session is not coming up. What are two reasons for this happening? (Choose two.)

A.    The inet protocol family is not configured on the QFabric system.
B.    There is a mismatching MED attribute configured.
C.    There are no RVIs configured on the QFabric system.
D.    The QFabric system is configured with two network Node groups.

Answer: AC

You have recently connected an aggregated interface between a server Node group and a blade chassis switch and the interface is down. Which three reasons would explain the interface being down? (Choose three.)

A.    The interface is using an unsupported or malfunctioning transceiver.
B.    Both sides of the connection have set LACP active.
C.    Both sides of the connection have set LACP passive.
D.    Aggregated interfaces are only supported on the network Node group.
E.    Spanning tree BPDUs have been received on the aggregated interface.

Answer: ACE

Which Routing Engine (RE) in a QFabric system acts as a BGP route reflector for internal reachability?

A.    the server Node group RE
B.    the network Node group RE
C.    the fabric control RE
D.    the fabric manager RE

Answer: C

A customer wants to change the management IP addresses for the fabric administrator and Director devices after the initial setup is completed. Which command should the customer enter on the Director device?

A.    /root/
B.    /root/
C.    /root/
D.    /root/

Answer: D

Thanks for reading the newest JN0-370 exam dumps! We recommend you to try the PREMIUM PassLeader JN0-370 dumps in VCE and PDF here: (281 Q&As Dumps)

Also, you can download that PassLeader JN0-370 braindumps from Google Drive: (FREE VERSION!!!)