PassLeader Premium Juniper JN0-370 Exam Dumps in VCE and PDF for Free Previewing (Question 181 – Question 200)

The newest Juniper JN0-370 dumps are available from PassLeader, you can get both JN0-370 VCE dumps and JN0-370 PDF dumps from PassLeader! PassLeader have added the newest JN0-370 exam questions into its JN0-370 VCE and PDF dumps now, the new JN0-370 braindumps will help you 100% passing the JNCIS-QF JN0-370 exam. Welcome to download the valid PassLeader JN0-370 dumps VCE and PDF here: https://www.passleader.com/jn0-370.html (281 Q&As Dumps)

Besides, download that PassLeader JN0-370 braindumps from Google Drive: https://drive.google.com/open?id=0B-ob6L_QjGLpbzlHTmN4Q2VTV1U (FREE VERSION!!!)

QUESTION 181
You are asked to configure a link aggregation group (LAG) between a QFabric system and an attached MX Series router. This LAG must support Layer 3 communications and must be associated with multiple VLANs. Which configuration approach should you use?

A.    Configure a Layer 3 LAG with the native-vlan option while ensuring that all desired VLANs are part of the native VLAN.
B.    Configure a Layer 2 LAG as a trunk port for the desired VLANs ensuring that the required RVIs are defined and associated with those VLANs.
C.    Configure a Layer 3 LAG with the vlan-tagging option with the required logical units and the parameters needed to support the desired VLANs.
D.    Configure a Layer 2 LAG with the vlan-tagging and inet options along with the required logical units and parameters needed to support the desired VLANs.

Answer: B

QUESTION 182
A customer added a new Node device under an existing Node group, but the new Node device is not discovered by the fabric manager. Which two CLI commands should help with troubleshooting? (Choose two.)

A.    Use the show log messages command on the new Node device.
B.    Use the show fabric administration inventory command on the fabric administrator.
C.    Use the show virtual-chassis protocol adjacency provisioning command on the Node group.
D.    Use the show chassis hardware command on the fabric administrator.

Answer: AC

QUESTION 183
Host A is connected to Node1 on VLAN10. Host B is connected to Node2 on VLAN20. VLAN interfaces for both VLANs are configured on a QFabric system. Host A wants to connect to Host B but the QFabric system is missing the ARP entry of Host B. Which statement is true?

A.    Node1 will generate the ARP request for Host B and flood it in VLAN20.
B.    The network Node group will generate the ARP request for Host B in VLAN20.
C.    Node2 will generate the ARP request in VLAN20.
D.    Node1 will drop the packet.

Answer: B

QUESTION 184
What does a Type-Length Value (TLV) for iSCSI provide in a QFabric system? (Choose two.)

A.    the ability to classify iSCSI flows on PFC channels
B.    the ability to create lossless iSCSI flows
C.    the ability to pause iSCSI flows
D.    the ability to create lossy iSCSI flows

Answer: AB

QUESTION 185
You want to maximize performance and ensure low latency for critical server applications using a QFabric system. What would be used as the first hop gateway for the applications?

A.    Layer 2 VLANs
B.    SRX Series devices
C.    RVIs
D.    MX Series devices

Answer: C

QUESTION 186
You are asked to set up a Director group. What information do you require? (Choose three.)

A.    the serial ID and MAC address range
B.    the alias device names and passwords
C.    the serial numbers of the Node devices
D.    three IP addresses and the management subnet
E.    the passwords for the Director group and system components

Answer: ADE

QUESTION 187
You are asked to attach a QFabric system to an existing Fibre Channel SAN. Which switch would enable you to accomplish this?

A.    FCoE transit switch
B.    Fibre Channel forwarder switch
C.    FCoE gateway switch
D.    Fibre Channel routing switch

Answer: C

QUESTION 188
Whenever you connect a Layer 2 switch to the xe-0/0/0 interface of the LC2 Node device in the server Node group of a QFabric system, the interface xe-0/0/0 on LC2 is disabled. What is causing this problem?

A.    The xe-0/0/0 interface on the LC2 Node device is not configured for family Ethernet switching.
B.    The LC2 Node device is not connected to the QFabric system.
C.    Interfaces on the server Node group can connect only to servers.
D.    The interface xe-0/0/0 of the LC2 Node device detects incoming BPDUs from a Layer 2 switch.

Answer: D

QUESTION 189
What must happen for QFabric system RVIs to become active?

A.    A network Node group is configured on the RVI VLAN.
B.    An operational Layer 2 interface is associated with the RVI VLAN.
C.    A server Node group is configured on the RVI VLAN.
D.    A Layer 3 interface is configured on the RVI VLAN.

Answer: B

QUESTION 190
What are two internal protocols in a QFabric system? (Choose two.)

A.    data center bridging protocol
B.    component monitoring protocol
C.    topology discovery protocol
D.    fabric control protocol

Answer: CD

QUESTION 191
Which Routing Engine (RE) in a QFabric system is responsible for compiling and distributing topology details to system components?

A.    the server Node group RE
B.    the network Node group RE
C.    the fabric control RE
D.    the fabric manager RE

Answer: D

QUESTION 192
You are powering on a QFabric system. What is the correct power-on sequence?

A.    Director devices, EX Series switches, Interconnect devices, Node devices
B.    EX Series switches, Interconnect devices, Node devices, Director devices
C.    Interconnect devices, EX Series switches, Node devices, Director devices
D.    EX Series switches, Director devices, Interconnect devices, Node devices

Answer: D

QUESTION 193
On which QFabric system Node group type can a cross-member Layer 3 LAG be configured?

A.    redundant server Node group
B.    Director Node group
C.    server Node group
D.    network Node group

Answer: D

QUESTION 194
You have enabled OSPF on your QFabric system. Which component will process the incoming hello packets?

A.    the active Routing Engine on the network Node group
B.    the PFE on the network Node group
C.    the Routing Engine on an elected member of the network Node group
D.    both Routing Engines on the network Node group

Answer: A

QUESTION 195
When bringing up a QFX3000-M QFabric system control plane network, which three actions should be performed? (Choose three.)

A.    Confirm data plane connections on EX Series switches are up.
B.    Apply site-specific configuration to EX Series switches.
C.    Verify connectivity and state of LAG between EX Series switches.
D.    Configure the network Node group.
E.    Power on the EX Series switches.

Answer: BCE

QUESTION 196
Which IP range does the fabric manager Routing Engine use for internal control plane device communication on the QFabric system?

A.    192.168.0.0/16
B.    172.16.0.0/16
C.    169.254.0.0/16
D.    127.0.0.0/8

Answer: C

QUESTION 197
After changing the Node group designation for a Node device, you notice that the Node device is disconnected. What is causing the problem?

A.    An incorrect command was issued on the fabric administrator.
B.    Moving the Node device from one group to another group causes the Node device to reboot.
C.    The Node device needs a manual reboot after changing the Node group designation.
D.    Server Node groups must retain the system default naming convention.

Answer: B

QUESTION 198
You need to determine the status of the Director devices from the fabric administrator. Which command would you use?

A.    show fabric administration inventory
B.    show chassis fabric connectivity
C.    show fabric director-group status
D.    show fabric administration inventory director-group status

Answer: D

QUESTION 199
What are two architectural goals of QFabric systems? (Choose two.)

A.    to provide a high speed WAN connection to the data center
B.    to view the entire system as a single administrative entity
C.    to eliminate the need to use security devices in the network
D.    to provide clear separation between control and data traffic for maximum scalability

Answer: AC

QUESTION 200
You are performing a nonstop software upgrade on a QFX3000-M QFabric system. According to Juniper Networks recommendations, which two upgrade processes are recommended? (Choose two.)

A.    Start the fabric upgrade, issue the Director group upgrade, and perform the Node group upgrades.
B.    Reboot the Interconnect devices and the fabric control Routing Engines at same time.
C.    Start the Director group upgrade, issue the fabric upgrade, and perform the Node group upgrades.
D.    Switch mastership of a Node group to the backup Node device before upgrading the master Node device.

Answer: CD


Thanks for reading the newest JN0-370 exam dumps! We recommend you to try the PREMIUM PassLeader JN0-370 dumps in VCE and PDF here: https://www.passleader.com/jn0-370.html (281 Q&As Dumps)

Also, you can download that PassLeader JN0-370 braindumps from Google Drive: https://drive.google.com/open?id=0B-ob6L_QjGLpbzlHTmN4Q2VTV1U (FREE VERSION!!!)