The newest Juniper JN0-370 dumps are available from PassLeader, you can get both JN0-370 VCE dumps and JN0-370 PDF dumps from PassLeader! PassLeader have added the newest JN0-370 exam questions into its JN0-370 VCE and PDF dumps now, the new JN0-370 braindumps will help you 100% passing the JNCIS-QF JN0-370 exam. Welcome to download the valid PassLeader JN0-370 dumps VCE and PDF here: https://www.passleader.com/jn0-370.html (281 Q&As Dumps)
Besides, download that PassLeader JN0-370 braindumps from Google Drive: https://drive.google.com/open?id=0B-ob6L_QjGLpbzlHTmN4Q2VTV1U (FREE VERSION!!!)
QUESTION 101
What are two characteristics of a traditional Ethernet LAN? (Choose two.)
A. Nodes share a physical medium.
B. Nodes can successfully transmit simultaneously.
C. It consists of a single broadcast domain.
D. Nodes use a step-up algorithm when collisions are detected.
Answer: AC
QUESTION 102
You are logged into a PE router participating in a Layer 3 VPN as defined in RFC 4364. You would like to ping the locally connected CE router’s interface. The address of the interface is 192.168.1.1; the VPN routing-instance is named VPN-A . Which command will accomplish this task?
A. ping routing-instance VPN-A 192.168.1.1
B. ping instance VPN-A 192.168.1.1
C. ping vpn-instance VPN-A 192.168.1.1
D. ping VPN-A 192.168.1.1
E. ping mpls l3vpn VPN-A 192.168.1.1
Answer: E
QUESTION 103
Before configuring an RSVP LSP in your network, you first apply a baseline configuration to all of the routers. Which three configuration elements are minimally required in the baseline? (Choose three.)
A. family mpls on the loopback interface
B. family mpls on the transit interfaces
C. protocols ldp for the appropriate interfaces
D. protocols mpls for the appropriate interfaces
E. protocols rsvp for the appropriate interfaces
Answer: BDE
QUESTION 104
From the output shown in the exhibit, what would happen to a packet destined for address 172.29.3.5?
A. The address is not in the aggregate range; the packet is sent to the Routing Engine.
B. The address is in the aggregate range; the packet will be silently dropped.
C. The address is not in the aggregate range; the packet will be forwarded.
D. The address is in the aggregate range; the packet will be dropped.
Answer: A
QUESTION 105
Your customer complains that their Layer 3 VPN is not passing traffic from one site to another. You assigned that customer to VPN-A. Which command on the PE router will confirm the presence of customer routes?
A. show route VPN-A
B. show route VPN-A table bgp.l2vpn.0
C. show route table inet.3 VPN-A
D. show route table VPN-A.inet.0
Answer: D
QUESTION 106
In an IS-IS network, which device represents the pseudo-node?
A. a designated intermediate system
B. an area border router
C. a router with an IS-IS export policy
D. a router connected to the backbone
Answer: A
QUESTION 107
Router B is an OSPF router connected to both Area 0 and Area 2. Area 2 has been configured as a totally stubby area. Which three LSA types does Router B suppress from Area 2? (Choose four.)
A. Router LSA
B. Network LSA
C. External LSA
D. Summary LSA
E. ASBR Summary LSA
Answer: ABCE
QUESTION 108
What is the size of the unique address used to identify each node on an Ethernet LAN?
A. 3 bytes
B. 6 bytes
C. 9 bytes
D. 12 bytes
Answer: B
QUESTION 109
Which two IS-IS packet types are used to maintain IS-IS database synchronization? (Choose two.)
A. IIH
B. LSP
C. PSNP
D. CSNP
Answer: CD
QUESTION 110
You notice that a route from internal BGP peer 192.168.1.1 is missing from the local route table. Which two commands would be used to help identify the source of the problem? (Choose two.)
A. show route bgp
B. show route protocol bgp hidden
C. show route receive-protocol bgp 192.168.1.1
D. show route advertising-protocol bgp 192.168.1.1
Answer: BC
QUESTION 111
What are three ways to configure IPv6 addresses in your network? (Choose three.)
A. Statically configure your IPv6 addresses.
B. Configure your IPv6 addresses using stateless auto configuration.
C. Configure your IPv6 addresses by setting up a DHCPv6 server.
D. Configure your IPv6 addresses by assigning your router a prefix list.
E. Configure your IPv6 addresses by configuring support for unicast-arp-negotiation.
Answer: ABC
QUESTION 112
Which two topologies shown in the exhibit could be implemented without a spanning-tree protocol? (Choose two.)
A. ring
B. tree
C. star
D. mesh
Answer: BC
QUESTION 113
In the exhibit, all routers are sending routes to Router B. Which routes will be advertised from Router B to Router E?
A. BGP routes learned from Router A only
B. BGP routes learned from Router D only
C. BGP routes learned from Routers A and C only
D. BGP routes learned from Routers A, C, and D only
Answer: D
QUESTION 114
In your RSVP network you have configured three separate LSPs to the same egress address. You have made no other configuration changes to the forwarding decisions made by the router. Which commands can you use to determine which LSP is being used to forward packets?
A. show route table inet.3
B. show route table inet.4
C. show rsvp neighbor
D. show rsvp session
Answer: A
QUESTION 115
Which two values are used by an RSTP bridge to remove stale BPDU information? (Choose two.)
A. Message Age
B. Forwarding Delay
C. Hello Time
D. Max Age
Answer: AD
QUESTION 116
After the MAC learning limit of 3000 is reached for the bd bridge domain as shown in the exhibit, what happens to frames that arrive that contain unknown unicast destination addresses?
A. They are flooded.
B. The are forwarded to the default gateway.
C. They are dropped.
D. They are forwarded to the IRB interface.
Answer: A
QUESTION 117
You have recently configured MSTP on two switches in your network to participate in the same MSTP region. You issue the show spanning-tree mstp configuration command on both switches and notice that the configuration digests do not match. What does this mismatch indicate?
A. Everything is functioning as expected because the configuration digests should not match.
B. You should ensure that the max-age and hello timers are equal on both switches.
C. You should ensure that the bridge IDs and priority values are unique on both switches.
D. You should ensure that the MSTIs and their VLAN IDs are equal on both switches.
Answer: D
QUESTION 118
You have a stub OSPF area running in your network. Your supervisor has asked you to build a virtual link across this area to connect new equipment acquired in a recent ISP acquisition. Which statement is correct about this scenario?
A. Type 5 LSAs would be blocked in a stub area.
B. Type 5 LSAs would carry external information across your transit area to the backbone.
C. Type 5 LSAs would be seen only in the newly attached area.
D. Type 5 LSAs would be converted to type 7 LSAs.
Answer: A
QUESTION 119
You own a small company and need to assign IPv6 addresses to your routers. Because you want to follow the guidelines spelled out in RFC 3177, you want to design your network with the correct prefixes. Which prefix would your ISP likely allocate to your company?
A. 47-bit prefix
B. 48-bit prefix
C. 64-bit prefix
D. 128-bit prefix
Answer: B
QUESTION 120
Your customer would like to forward traffic using DLCI 600 and maintain Layer 2 information across a VPN. Which solution will meet these requirements?
A. a Layer 3 VPN
B. a Layer 2 VPN
C. Virtual Private LAN Service (VPLS)
D. an IPsec VPN
Answer: B
Thanks for reading the newest JN0-370 exam dumps! We recommend you to try the PREMIUM PassLeader JN0-370 dumps in VCE and PDF here: https://www.passleader.com/jn0-370.html (281 Q&As Dumps)
Also, you can download that PassLeader JN0-370 braindumps from Google Drive: https://drive.google.com/open?id=0B-ob6L_QjGLpbzlHTmN4Q2VTV1U (FREE VERSION!!!)
