[14-May-2021] New PassLeader JN0-334 JNCIS-SEC Dumps with VCE and PDF (New Questions)

The newest Juniper JN0-334 dumps are available from PassLeader, you can get both JN0-334 VCE dumps and JN0-334 PDF dumps from PassLeader! PassLeader have added the newest JN0-334 exam questions into its JN0-334 VCE and PDF dumps now, the new JN0-334 braindumps will help you 100% passing the JNCIS-SEC JN0-334 exam. Welcome to download the valid PassLeader JN0-334 dumps VCE and PDF here: https://www.passleader.com/jn0-334.html (95 Q&As Dumps)

Besides, download that PassLeader JN0-334 braindumps from Google Drive: https://drive.google.com/open?id=1koMlSA_BaaHIZVC8FmUpiW8csKjj-1te (FREE VERSION!!!)

NEW QUESTION 81
At which step in the packet flow are Junos Screen checks applied?

A.    prior to the route lookup
B.    prior to security policy processing
C.    after ALG services are applied
D.    after source NAT services are applied

Answer: A

NEW QUESTION 82
You need to implement Junos Screen options to protect traffic coming through the ge-0/0/0 and ge-0/0/1 interfaces which are located in the trust and DMZ zones, respectively. Where would you enable the Junos Screen options?

A.    on the ge-0/0/0 and ge-0/0/1 interfaces
B.    in the trust and DMZ zone settings
C.    in a security policy
D.    in the global security zone settings

Answer: B

NEW QUESTION 83
What are three valid actions for a then statement in a security policy? (Choose three.)

A.    reject
B.    discard
C.    accept
D.    deny
E.    permit

Answer: ADE

NEW QUESTION 84
Which two statements are correct regarding reth interfaces? (Choose two.)

A.    Child interfaces must be in the same slot on both nodes.
B.    Child interfaces do not need to be in the same slot on both nodes.
C.    Child interfaces must be the same Ethernet interface type.
D.    Child interfaces can be a mixture of Ethernet interface types.

Answer: BC

NEW QUESTION 85
You are asked to establish an IPsec VPN between two sites. You are also required to establish an OSPFv2 adjacency across this VPN. Which type of VPN should you select?

A.    policy-based VPN
B.    protocol-based VPN
C.    destination-based VPN
D.    route-based VPN

Answer: D

NEW QUESTION 86
You are building a VPN tunnel between two SRX Series devices. You want the tunnel to always be established, even if there is no traffic to send. Which action would be used to achieve this goal?

A.    Configure an RPM probe to constantly ping across the links.
B.    Configure vpn-monitor with the optimized parameter on the tunnel.
C.    Configure establish-tunnels with the immediately parameter.
D.    Configure the OSPF demand-circuit feature on the tunnel interface.

Answer: C

NEW QUESTION 87
What is the default timeout for a TCP session on an SRX Series device?

A.    1 minute
B.    1 hour
C.    30 seconds
D.    30 minutes

Answer: D

NEW QUESTION 88
Which two are negotiated during Phase 2 of an IPsec VPN tunnel establishment? (Choose two.)

A.    security protocol
B.    VPN monitor interval
C.    UDP port number
D.    proxy IDs

Answer: AD

NEW QUESTION 89
You want to show interface-specific zone information and statistics. Which operational command would be used to accomplish this?

A.    show security zones detail
B.    show interfaces ge-0/0/3.0
C.    show interfaces terse
D.    show interfaces ge-0/0/3.0 extensive

Answer: D

NEW QUESTION 90
You have just configured source NAT with a pool of addresses within the same subnet as the egress interface. What else must be configured to make the addresses in the pool usable?

A.    static NAT
B.    proxy ARP
C.    address persistence
D.    destination NAT

Answer: B

NEW QUESTION 91
The AppQoE module of AppSecure provides which function?

A.    The AppQoE module provides routing, based on network conditions.
B.    The AppQoE module prioritizes important applications.
C.    The AppQoE module provides application-based routing.
D.    The AppQoE module blocks access to risky applications.

Answer: C

NEW QUESTION 92
Which two statements describe application-layer gateways (ALGs)? (Choose two.)

A.    ALGs are designed for specific protocols that require multiple sessions.
B.    ALGs are used with protocols that use multiple ports.
C.    ALGs can only be configured using Security Director.
D.    ALGs are designed for specific protocols that use a single TCP session.

Answer: AB

NEW QUESTION 93
……


Thanks for reading the newest JN0-334 exam dumps! We recommend you to try the PREMIUM PassLeader JN0-334 dumps in VCE and PDF here: https://www.passleader.com/jn0-334.html (95 Q&As Dumps)

Also, you can download that PassLeader JN0-334 braindumps from Google Drive: https://drive.google.com/open?id=1koMlSA_BaaHIZVC8FmUpiW8csKjj-1te (FREE VERSION!!!)