[3-Nov-2022] New PassLeader JN0-649 JNCIP-ENT Dumps with VCE and PDF (New Questions)

The newest Juniper JN0-649 dumps are available from PassLeader, you can get both JN0-649 VCE dumps and JN0-649 PDF dumps from PassLeader! PassLeader have added the newest JN0-649 exam questions into its JN0-649 VCE and PDF dumps now, the new JN0-649 braindumps will help you 100% passing the JNCIP-ENT JN0-649 exam. Welcome to download the valid PassLeader JN0-649 dumps VCE and PDF here: https://www.passleader.com/jn0-649.html (195 Q&As Dumps)

Besides, download that PassLeader JN0-649 braindumps from Google Drive: https://drive.google.com/drive/folders/1Tcd9VwoT91AAR95GbqPWuDHeAGbFRGwW (FREE VERSION!!!)

NEW QUESTION 171
You must provide network connectivity to hosts that fail authentication. In this scenario, what would be used in a network secured with 802.1X to satisfy this requirement?

A.    Configure the native-vlan-id parameter on the port.
B.    Use the server-reject-vlan command to specify a guest VLAN.
C.    Configure a secondary IP address on the port for unauthenticated hosts.
D.    Configure the port as a spanning tree edge port.

Answer: B

NEW QUESTION 172
A Layer 2 connection does not expend across data centers. The IP subnet in a Layer 2 domain is confined within a single data center. Which EVPN route type is used to communicate prefixes between the data centers?

A.    Type 1
B.    Type 2
C.    Type 4
D.    Type 5

Answer: D

NEW QUESTION 173
You are asked to implement fault tolerant RPs in your multicast network. Which two solutions would accomplish this behavior? (Choose two.)

A.    Use BFD with statically defined RPs.
B.    Use MSDP with statically defined RPs.
C.    Use anycast PIM with statically defined RPs.
D.    Use IGMPv3 with statically defined RPs.

Answer: BC

NEW QUESTION 174
Which three MSTP parameters must match on all switches in the same MST region? (Choose three.)

A.    forwarding delay
B.    bridge priority
C.    revision number
D.    MSTI-to-VLAN mapping
E.    configuration name

Answer: BCE

NEW QUESTION 175
When using wide metrics, which two statements about route advertisement between IS-IS levels are correct? (Choose two.)

A.    Level 1 and Level 2 routers do not advertise Level 2 routes into the Level 1 area by default.
B.    Level 1 routes are advertised to Level 2 routers by default.
C.    If wide-metrics-only is configured, Level 1 routes are not advertised to Level 2 routers by default.
D.    Level 1 routes advertised as external routes into Level 1 are not advertised to any Level 2 routers by default.

Answer: AC

NEW QUESTION 176
What are two similarities between OSPFv2 and OSPFv3? (Choose two.)

A.    virtual links
B.    support for multiple instances per link
C.    32-bit router ID
D.    protocol processing per link, not per subnet

Answer: AC

NEW QUESTION 177
Your EX Series switch has IP telephones and computers connected to a single switch port. You are considering implementing the voice VLAN feature to help with this setup. In this scenario, which two statements are correct? (Choose two.)

A.    The voice VLAN feature must be used with LLDP-MED to associate VLAN ID and 802.1p values with the traffic.
B.    The interfaces must be configured as access ports.
C.    Assigning the incoming voice and data traffic to separate VLANs enables the ability to prioritize the traffic using CoS.
D.    The voice VLAN feature will enable incoming tagged data and voice traffic to be associated with separate VLANs.

Answer: BC

NEW QUESTION 178
You are deploying new Juniper EX Series switches in a network that currently is using Cisco’s Per-VLAN spanning tree plus (PVST+) and you must provide compatibility with this environment. Which spanning tree protocol do you deploy in this scenario?

A.    STP
B.    MSTP
C.    VSTP
D.    RSTP

Answer: B

NEW QUESTION 179
A modified deficit round-robin scheduler is defined by which three variables? (Choose three.)

A.    priority
B.    WRED
C.    transmit rate
D.    Layer 3 fields
E.    buffer size

Answer: ABC

NEW QUESTION 180
You are asked to configure an 802.1X solution that supports dynamic VLAN assignment. In this scenario, which two modes support using vendor-specific attributes (VSAs)? (Choose two.)

A.    static MAC bypass mode
B.    single-secure supplicant mode
C.    multiple supplicant mode
D.    single supplicant mode

Answer: BC

NEW QUESTION 181
You are deploying an 802.1X solution and must determine what would happen if clients are unable to re-authenticate to the RADIUS server. In this scenario, which configuration would provide access to the network if the supplicant is already authenticated?

A.    move
B.    permit
C.    deny
D.    sustain

Answer: D

NEW QUESTION 182
You are deploying IP phones in your enterprise network that must receive their power through their Ethernet connection. You are using your EX Series switch’s PoE ports that support IEEE 802.3af. In this scenario, what is the maximum amount of power allocated to each interface?

A.    10.2 W
B.    15.4 W
C.    30 W
D.    50 W

Answer: B

NEW QUESTION 183
You are deploying IP phones in your enterprise networks. When plugged in, the IP phones must be automatically provided with the correct VLAN ID needed for sending voice traffic to the EX Series switches. In this scenario, which two solutions are required to accomplish this task? (Choose two.)

A.    Enable LLDP-MED on appropriate access interfaces.
B.    Create two VLANs and assign them as VLAN members to the appropriate access interfaces.
C.    Enable the voice VLAN feature with the appropriate access interfaces and VLAN ID for voice traffic.
D.    Use LLDP on appropriate interfaces.

Answer: AC

NEW QUESTION 184
You are deploying IP phones in your enterprise networks. When plugged in, the IP phones must automatically negotiate the power requirements for the new connection with the EX Series switches. In this scenario, which protocol should be used to enable this behavior?

A.    CDP
B.    MP-BGP
C.    LLDP-MED
D.    LLDP

Answer: C

NEW QUESTION 185
Your network is multihomed to two ISPs. The BGP sessions are established; however, the ISP peers are not receiving any routes. Which two statements are correct about troubleshooting your configuration? (Choose two.)

A.    Verify the import policies on your router.
B.    Verify that the BGP routes are active in your routing table.
C.    Verify the export policies on your router.
D.    Verity that the multihop settings are configured on your router.

Answer: CD

NEW QUESTION 186
You are running OSPF as your IGP. The interfaces connecting two routers are in the ExStart state. You notice that something is incorrect with the configuration. Referring to the exhibit:
JN0-649-Exam-Dumps-1861
Which statement is correct?

A.    The subnet mask is incorrect.
B.    The MTU setting are incorrect.
C.    The interface type is incorrect.
D.    The IP addresses are incorrect.

Answer: D

NEW QUESTION 187
You have scheduled maintenance operations for one of the devices in your OSPF network. Referring to the exhibit:
JN0-649-Exam-Dumps-1871
Which three statements are correct? (Choose three.)

A.    R1 does not participate in OSPF routing.
B.    Any traffic destined for networks that terminate on R1 will still be forwarded to R1.
C.    The metrics for all transit interfaces on R1 is set to the maximum value of 65,535.
D.    R1 participates in OSPF routing but does not send or receive transit traffic.
E.    R1 does not send or receive transit traffic during the maintenance window even if no alternative paths exist to the given destination.

Answer: BCD

NEW QUESTION 188
You recently committed a change to a router to reject OSPF routes sourced from area 10. However, you are still seeing area 10 routes in the routing table. Referring to the exhibit:
JN0-649-Exam-Dumps-1881
Which statement is correct?

A.    The OSPF protocol is first matched by find-ospf and accepted.
B.    The routes only timeout after 24 hours.
C.    The routes remain in the table until the device is rebooted.
D.    The routes remain in the table until the routing daemon is restarted.

Answer: D

NEW QUESTION 189
Referring to the exhibit:
JN0-649-Exam-Dumps-1891
A PIM-SM network is set up to enable communication between multicast devices. Which two statements are true? (Choose two.)

A.    Before the formation of the rendezvous-point tree, a join message is sent from R1 to R3.
B.    Before the formation of the rendezvous-point tree, an IGMP is sent from the Receiver to R1.
C.    Before the formation of the rendezvous-point tree, an IGMP is sent from the Source to R5.
D.    Before the formation of the rendezvous-point tree, a join message is sent from R1 to R5.

Answer: BC

NEW QUESTION 190
Your network has an unmanaged switch between the hosts and your EX Series switch. After the traffic enters the EX Series switch, each host must be on a separate VLAN. Referring to the exhibit:
JN0-649-Exam-Dumps-1901
How would you accomplish this task?

A.    Configure an input firewall filter on interface ge-0/0/3 to match the source MAC or IP address of the hosts to assign the VLANs.
B.    Configure an output firewall filter on interface ge-0/0/1 to match the destination MAC or IP address of the hosts to assign the VLANs.
C.    Configure interface ge-0/0/3 to a mode trunk to assign the VLANs.
D.    Configure VSTP on interface ge-0/0/1 to assign the VLANs.

Answer: C

NEW QUESTION 191
You are troubleshooting an EVPN-VXLAN IP fabric and observe the loop shown in the exhibit:
JN0-649-Exam-Dumps-1911
Which two steps would you take to further troubleshoot this problem? (Choose two.)

A.    Verify that the same ESI is configured on the link from the host and that it matches the source.
B.    Issue the show route table bgp.evpn.0 command on Leaf2 and verify that Type 4 routes are present.
C.    Issue the show route table bgp.evpn.0 command on Leaf2 and verify that Type 3 routes are present.
D.    Verify that the same ESI is configured on the two links from the source.

Answer: BC

NEW QUESTION 192
You want to provide Layer 2 connectivity between campus sites using Ethernet switches through a metro Ethernet service provider who is using Q-in-Q tagging on their network. Referring to the exhibit:
JN0-649-Exam-Dumps-1921
What are two design considerations in this environment? (Choose two.)

A.    VXLAN could be implemented on your network across this service provider network.
B.    Each campus switch shown must have a C-Tag 300 configured.
C.    L2PT is required on the SP network to support the spanning tree protocol.
D.    Each campus switch shown must have S-Tag 300 configured.

Answer: CD

NEW QUESTION 193
……


Thanks for reading the newest JN0-649 exam dumps! We recommend you to try the PREMIUM PassLeader JN0-649 dumps in VCE and PDF here: https://www.passleader.com/jn0-649.html (195 Q&As Dumps)

Also, you can download that PassLeader JN0-649 braindumps from Google Drive: https://drive.google.com/drive/folders/1Tcd9VwoT91AAR95GbqPWuDHeAGbFRGwW (FREE VERSION!!!)